Testing waters on selling my "set up". Been on the car for 30k miles and rides great. Factory MKVI Golf R dampers and 4 door specific VWRacing springs. Had them on my MKV SportWagen 2.0T. Still on the car at the moment. 425 obo? Sent from my SM-G950U1 using Tapatalk
Selling my suspension setup as I finally caved in and got some KWs. Been on the car for 30k miles and rides great. Factory MKVI Golf R dampers and 4 door specific VWRacing springs. Had them on my MKV SportWagen 2.0T. Still on the car at the moment. 425 obo? Sent from my SM-G950U1 using Tapatalk
New KB aluminium water block. Raised 54mm cam bore,1.8 lifter spacing,bronze lifter bushings. Complete stud kit(1/2" head,oil pan,timing cover). Cam bearings installed,aluminium main caps,six bolt mains,4.500 bore. All block prep has been completed(push rod clearancing,belt drive clearancing. $8695 Don (708)987-2394. Addison, IL 60101 (708) 987-2394
days agoCary, IL+10 milesAuto Parts for Sale
I am selling a set of wheels and tires that were originally on a 2015 Camaro SS. I purchased these from Discount Tire in November 2016, so they have seen 3 winters. All told they have 12K miles on them. You could probably squeeze another winter out of them, but that s totally up to you. WHEELS: All 4 are replica factory in matte black finish. All four measure 20X9. Bolt pattern is 5X120. Offset...
This is a complete setup consisting of... -DMPE M5 14-71 supercharger -Mike Janis custom machined bottom outlet plate -Janis insert -Janis custom spacer -Knut 3 hole carbon hat with Janis spray bar -Restraint plate -Barrel valve -JBR distribution block -Throttle cable bracket -All hoses and fittings pictured with the exception of the flow meter -One 14mm pulley -Additional DMPE insert, spacer, ...
View attachment 4285100 View attachment 4285101 View attachment 4285102 View attachment 4285103 View attachment 4285104 A bit rough...
2.L COPO Whipple supercharger for sale Blower has been upgraded by DMPE. Upgrades include ceramic bearings, coated rotors, optimized clearances, etc. The Cost of upgrades alone were $2750! Blower has 12 passes on it. Selling with Intercooler and top pulley of your choice, either 3.375, 3.250, 3.125. (lower intake not included) Price $4200. Also have a set of COPO fuel rails and pulley/tensioner...
Bench seat bolts and brackets out of a 71 Bay Window Bus. 4 complete 1 bolt only Shipping included to continental US
FOR SALE: FRESH and ready-to-go 410 cu in RACING ENGINE 400 Bowtie block; 4 bolt main Complete, less carburetor Bore 4.170 Stroke 3.75 J & E Pistons, teflon & ceramic-coated, 14.0 compression Total Seal Zero Gap rings Casidium-coated wrist pins Callies Magnum forged crankshaft 6 inch Oliver rods Comp Cams roller cam 278/274 duration, 698/660 lift, lobe center 106 Crower 904 roller lifters Bronz...
looking for a good condition rear big bumper cover replacement. mine is a bit rough and looking to see if anyone has one collecting dust local before i order one new. thanks
Fie spud Miller 8amp mag with coil, mount bracket and Chevy base. antioch, IL 60002 (262) 960-0408
Billet fab 4 pickup dry sump pan never bolted on.. antioch, IL 60002 (262) 960-0408
Here's a very nice pair of 1CM mercury Heads. These came off a motor that was purchased from a local Ford Dealership New and used to power a boat on the Hudson River (fresh water).The builder didn't like the way the flatty powered the boat so he swapped out the motor after a year or two and stashed it in a storage building for about 35 years until i bought it.No damage that i can see .These wor...
ATECO 555/756 CARB $21,995.00 Ready To Run Drop In... Horse Power 756 @ 6000 RPM, Torque 715 @ 4700 RPM, Bore & Stroke 4.560 X 4.250, Ratio 10 to 1, Fuel Requirement 93 Octane. Component List: Dart Big M Block w/ Steel Main Caps Bored to 4.560", 6.385" Lunati 4340 Steel H-Beam Rods w/ ARP 2000 7/16 Cap Bolts, 4.250 Stroke 4340 Forged Steel Internal Balance w/ Center Counter Weights 2pc Seal Cra...
ATECO 555/756 CARB $21,995.00 Ready To Run Drop In... Horse Power 756 @ 6000 RPM, Torque 715 @ 4700 RPM, Bore & Stroke 4.560 X 4.250, Ratio 10 to 1, Fuel Requirement 93 Octane. Component List: Dart Big M Block w/ Steel Main Caps Bored to 4.560", 6.385" Lunati 4340 Steel H-Beam Rods w/ ARP 2000 7/16 Cap Bolts, 4.250 Stroke 4340 Forged Steel Internal Balance w/ Center Counter Weights 2pc Seal Cra...